Archives of Environmental Protection

The impacts of long-term polycyclic aromatic hydrocarbons (PAHs) and heavy metal pollution on soil microbial communities functioning were studied in soils taken from an old coke plant. The concentrations of PAHs in the tested soils ranged from 171 to 2137 mg kg-1. From the group of tested heavy metals, concentrations of lead were found to be the highest, ranging from 57 to 3478 mg kg-1, while zinc concentrations varied from 247 to 704 mg kg-1 and nickel from 10 to 666 mg kg-1. High dehydrogenase, acid and alkaline phosphatase activities were observed in the most contaminated soil. This may indicate bacterial adaptation to long-term heavy metal and hydrocarbon contamination. However, the Community Level Physiological Profiles (CLPPs) analysis showed that the microbial functional diversity was reduced and influenced to a higher extent by some metals (Pb, Ni), moisture and conductivity than by PAHs.

In the present study, the enrichment and isolation of textile effluent decolorizing bacteria were carried out in wheat bran (WB) medium. The isolated bacterium Providencia rettgeri strain HSL1 was then tested for decolorization of textile effluent in consortium with a dyestuff degrading fungus Aspergillus ochraceus NCIM 1146. Decolorization study suggests that A. ochraceus NCIM 1146 and P. rettgeri strain HSL1 alone re moves only 6 and 32% of textile effluent American Dye Manufacturing Institute respectively in 30 h at 30 ±0.2°C of microaerophilic incubation, while the fungal-bacterial consortium does 92% ADMI removal within the same time period. The fungal-bacterial consortium exhibited enhanced decolorization rate due to the induction in activities of catalytic enzymes laccase (196%), lignin peroxidase (77%), azoreductase (80%) and NADH-DCIP reductase (84%). The HPLC analysis confirmed the biodegradation of textile effluent into various metabolites. Detoxification studies of textile effluent before and after treatment with fungal-bacterial consortium revealed reduced toxicity of degradation metabolites. The efficient degradation and detoxification by fungal-bacterial consortium pre-grown in agricultural based medium thus suggest a promising approach in designing low-cost treatment technologies for textile effluent.

New York Bay is one of the most important transition regions of ships trading to east America. The region plays an important role in the commerce of the New York metropolitan area. The area is surrounded with the coasts that have various levels of environmental sensitivity. The area accommodates high diversity of native ecosystems and species that are rather vulnerable in case of oil spill. Thus getting well informed about the likelihood, or fate, of oil spills around this region is of great importance so that proactive measures can be taken. The purpose of this study is to investigate the oil spill and predict the future accidents likely to be encountered around the Bay of New York. Two trajectory models have been conducted for the study. ADIOS (Automated Data Inquiry for Oil Spills), has been conducted for natural degradation calculations, and, GNOME (General NOAA Operational Modeling Environment), has been conducted for surface spread simulation. The results gained through these efforts are hoped to be useful for many organizations dealing with oil spill response operations and contribute to an effective and efficient coordination among the relevant institutions.

Silver nanoparticles (AgNPs) are widely used in numerous industries and areas of daily life, mainly as antimicrobial agents. The particles size is very important, but still not suffi ciently recognized parameter infl uencing the toxicity of nanosilver. The aim of this study was to investigate the cytotoxic effects of AgNPs with different particle size (~ 10, 40 and 100 nm). The study was conducted on both reproductive and pulmonary cells (CHO-9, 15P-1 and RAW264.7). We tested the effects of AgNPs on cell viability, cell membrane integrity, mitochondrial metabolic activity, lipid peroxidation, total oxidative and antioxidative status of cells and oxidative DNA damage. All kinds of AgNPs showed strong cytotoxic activity at low concentrations (2÷13 μg/ml), and caused an overproduction of reactive oxygen species (ROS) at concentrations lower than cytotoxic ones. The ROS being formed in the cells induced oxidative damage of DNA in alkaline comet assay. The most toxic was AgNPs<10 nm. The results indicate that the silver nanoparticles, especially less than 10 nm, may be harmful to the organisms. Therefore, risk should be considered when using nanosilver preparations and provide appropriate protective measures when they are applied.

22 representative antibiotics, including 8 quinolones (QNs), 9 sulfonamides (SAs), and 5 macrolides (MCs) were selected to investigate their occurrence and removal efficiencies in a Wastewater Treatment Plant (WWTP) and their distribution in the receiving water of the Chaobai River in Beijing, China. Water quality monitoring was performed in an integrated way at different selected points in the WWTP to explore the potential mechanism of antibiotics removal during wastewater treatment. Water quality of the Chaobai River was also analyzed to examine environmental distribution in a river ecosystem. The results showed that within all the 22 compounds examined, 10 antibiotics were quantified in wastewater influent, 10 in effluent, and 7 in river. Sulfadiazine (SDZ, 396 ng/L) and Sulfamethazine (SMZ, 382 ng/L) were the dominating antibiotics in the influent. Both the conventional treatment and advanced Biological Aerated Filter (BAF) system was important for the removal of antibiotics from the wastewater. And the concentrations of selected antibiotics were ranged from 0-41.8 ng/L in the effluent-receiving river. Despite the fact that the concentrations were reduced more than 50% compared to effluent concentrations, WWTP discharge was still regarded as a dominant point-source input of antibiotics into the Chaobai River.

The objective of this study was to investigate the possibility of using natural and bacteria-modified Erzurum clayey soil with Methylobacterium extorquens as an alternative to high cost commercial adsorbent materials for the removal of copper from aqueous solution. The copper concentrations in the samples of the polluted river water and CuCl2 solutions treated by the natural and bacteria-modified Erzurum clayey soil (ECS) have been determined by spectrophotometric method. Firstly, the surface of ECS was modified with M. extorquens and surface functionality was increased. Then, the adsorption of Cu (II) from solution phases was studied with respect to varying metal concentration, pH, and temperature and agitation time. The maximum adsorption of Cu (II) for natural and bacteria-modified Erzurum clayey soil was observed at pH: 5.0. At different copper concentrations, copper adsorption analysis was performed on 1 g using clay soil or modified clay soil. Maximum adsorption of Cu (II) was obtained as 45.7 and 48.1 mg g-1 at initial concentration (50 mg/50 mL) and optimal conditions by natural and bacteria-modified clay soil, respectively. The copper concentration was decreased in the substantial amount of the leachates solutions of natural and bacteria-modified clay soil. Langmuir and Freundlich isotherms were used to describe the adsorption behavior of Cu (II) ions. The results showed that modified clay soil had a high level of adsorption capacity for copper ion. The various thermodynamic parameters such as ΔG°, ΔH° and ΔS° were analyzed to observe the nature of adsorption. The structural properties of the natural and bacteria-modified-ECS have been characterized by SEM, FTIR and XRD techniques. Consequently, it was concluded that the bacteria-modified clay soil could be successfully used for the removal of the copper ions from the aqueous solutions.

In this study, a pilot-scale subsurface wastewater infiltration system (SWIS) was deployed to study landscape water treatment. The goal of the study was to investigate the effects of hydraulic loading on pollutant removal and the spatial distribution of biofilm properties in SWIS. Results showed that the efficiencies of chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) removal degraded as hydraulic loading increased. Furthermore, quantities of the biofilm properties parameter s increased with the hydraulic loading. Polysaccharide and protein levels ranged from 560 to 1110 μg/g filler and 60 to 190 μg/g filler, respectively, at a hydraulic loading of 0.2 m/d. At a hydraulic loading of 0.4 m/d, the quantities of polysaccharide and protein ranged from 1200 to 3300 μg/g filler and 80 to 290 μg/g filler, respectively. Biofilm intensity and biofilm activity per unit weight decreased with the increase in hydraulic loading.

This paper deals with wastewater treatment systems placed in motorway service areas (MSAs). In the years 2008-2009 eight of such facilities installed on the stretch of the A2 motorway between Poznań and Nowy Tomyśl were examined and analyzed. The system consists of a septic tank, a submerged aerated biofilter and an outflow filter. The volume of traffic on the highway was analyzed, the amount of water use was measured and peak factors were calculated. On this basis it was concluded that the inflows to the wastewater treatment systems in many cases exceeded the nominal design values.

Based on the analysis of effluent quality it was found that the effects of plant operation in large part did not meet the requirements. It was found that the bioreactor aeration system and the design of the suspension separator (outflow filter) should be modified. One of the solutions was to use the soil-reed bed for wastewater treatment. The treatment of wastewater from the MSAs is a task that must take into account the unusual character of these facilities and the atypical quality of the effluent.

The sorption isotherm and sorption kinetics of NH4+ by the Fen River reservoir sediment were investigated for a better understanding of the NH4+ sorption characteristics and parameters. The results showed that Q (adsorption content) increased with the increase of Ceq (equilibrium concentration), sorption isotherms could be described by Freundlich equation (R2 from 0.97 to 0.99). Cation exchange capacity (CEC) had a significant correlation with the parameters K and n (R2 was 0.85 and 0.95, respectively). The ENC0 (Ceq as Q was zero) of S1, S2, S3 and S4 was 1.25, 0.57, 1.15 and 1.14 mg L-1, respectively, and they were less than the NH4+ concentrations in reservoir water. The sediments released NH4+ to the Fen River reservoir water and acted as a pollution source, in the form of complex and heterogeneous adsorbents. The NH4+ adsorption kinetic process was composed of ‘fast’ and ‘slow’ reaction patterns and could be fitted using both Elovich equation and Pseudo second-equation. More than one-step may be involved in the NH4+ sorption processes, and interior diffusion was not dominant ion action.

Carbon dioxide sequestration and its long-term immobilisation in biomass is recently an extremely significant problem. Its greatest reserves occur in forests growing all over the globe. A human being, through their conscious action, ought to affect, among other things, the amount of carbon dioxide discharged into the atmosphere and its rational management. Here, quite a good solution seems to be the immobilisation of CO2 in biomass of plants, and in particular, in trees, characterised by their longevity, which are used most frequently for that purpose.

Such carbon dioxide management allows for its several-decade immobilisation within living plants, while a further processing of wood mass allows for halting it for consecutive years in products manufactured. Additionally, in the case when within a selected land planted with trees the effluent irrigation is being carried out, simultaneous sewage treatment is also an advantage. By using plants characterised by intense increment in biomass within facilities, also biogens occurring in effluents may be effectively removed.

In the analysed case, sewage treatment consisted in entry of household sewage into a prepared surface which was previously subject to mechanical purification. All the sections were sown with grass mixture and plantings of poplar were used. Observations were made during the period of 17 years. The effluents entered onto the surface of the sections and the effluents outflowing from the facility were subject to a physicochemical analysis in order to determine the operational efficiency of a plant - soil treatment system. Also, a threefold inventory of a forest stand was made in order to determine the increment in trees.

The last inventory was made in 2014. Based on dendrological characteristics, the average volume of wood mass obtained from the land irrigated with effluents was assessed.

A rational management of effluents on the grounds without any central drainage allows for a parallel solution to some problems. First of all, purification of effluents in a natural environment by closing the matter cycle, and additionally contributing to the limitation of carbon dioxide emission by its halting in plant biomass.

The objective of the study was to compare the impact of three systems of multiannual fertilization applied in two long-term field experiments on the content of phenolic compounds in the soil. In the study, both natural (manure, slurry) and mineral (NPK) fertilizers were used, along with combined, organic-and-mineral fertilization. Experiment I was established in 1972 on grey brown podzolic soil; experiment II, in 1973 on brown soil. In both experiments crops were cultivated in a 7-year rotation, with a 75% share of cereals. The experimental samples were taken from the top layer of soil after 36 (experiment I) and 35 (experiment II) years following the establishment of the experiments. It was demonstrated that the presence of phenolic compounds in the soils was significantly dependent on the contents of organic C and total N, type of soil and the type and dose of used fertilizers. In grey brown podzolic soil, the content of total phenolic compounds was at a lower level than the content found in brown soil. Multiannual fertilization contributed to an increase in the content of total phenolic compounds in relation to the values obtained in control objects, which was particularly reflected in the soil originating from objects fertilized with slurry applied at a dose being equivalent to manure in terms of the amount of introduced organic carbon. The percentage of water-soluble phenols in the total content of these compounds in grey brown podzolic soil was at the level of 18.4%, while in brown soil it amounted to 29.1%.

This paper studies the assessment of sensitivity to land degradation of Deliblato sands (the northern part of Serbia), as a special nature reserve. Sandy soils of Deliblato sands are highly sensitive to degradation (given their fragility), while the system of land use is regulated according to the law, consisting of three zones under protection. Based on the MEDALUS approach and the characteristics of the study area, four main factors were considered for evaluation: soil, climate, vegetation and management. Several indicators affecting the quality of each factor were identified. Each indicator was quantified according to its quality and given a weighting of between 1.0 and 2.0. ArcGIS 9 was utilized to analyze and prepare the layers of quality maps, using the geometric mean to integrate the individual indicator map. In turn, the geometric mean of all four quality indices was used to generate sensitivity of land degradation status map. Results showed that 56.26% of the area is classified as critical; 43.18% as fragile; 0.55% as potentially affected and 0.01% as not affected by degradation. The values of vegetation quality index, expressed as coverage, diversity of vegetation functions and management policy during the protection regime are clearly represented through correlation coefficient (0.87 and 0.47).

The influence of sewage sludge torrefaction temperature on fuel properties was investigated. Non-lignocellulosic waste thermal treatment experiment was conducted within 1 h residence time, under the following temperatures: 200, 220, 240, 260, 280 and 300°C. Sawdust was used as lignocellulosic reference material. The following parameters of biochar have been measured: moisture, higher heating value, ash content, volatile compounds and sulfur content. Sawdust biochar has been confirmed to be a good quality solid fuel. High ash and sulfur content may be an obstacle for biochar energy reuse. The best temperature profile for sawdust torrefaction and fuel production for 1 h residence time was 220°C. At this temperature the product contained 84% of initial energy while decreased the mass by 25%. The best temperature profile for sewage sludge was 240°C. The energy residue was 91% and the mass residue was 85%. Higher temperatures in both cases caused excessive mass and energy losses.