The paper presents an analysis of the sustainable development of electricity generation sources in the National Power System (NPS). The criteria to be met by sustainable power systems were determined. The paper delineates the power balance of centrally dispatched power generation units (CDPGU), which is required for the secure work of the NPS until 2035. 19 prospective electricity generation technologies were defined. They were divided into the following three groups: system power plants, large and medium combined heat and power (CHP) plants, as well as small power plants and CHP plants (distributed sources). The quantities to characterize the energy effectiveness and CO2 emission of the energy generation technologies analyzed were determined. The unit electricity generation costs, discounted for 2018, including the costs of CO2 emission allowance, were determined for the particular technologies. The roadmap of the sustainable development of the generation sources in the NPS between 2020 and 2035 was proposed. The results of the calculations and analyses were presented in tables and figure
The article compares the management of energy resources in Poland and Ukraine over the period 2000–2017. The analysis took changes in the volume of coal, oil and natural gas resources into consideration. The indicators of supplies of these fuels for Poland and Ukraine have additionally been compared with selected EU countries. In order to assess energy security of Poland and Ukraine, the changes in the primary energy consumption have been analyzed in general in first order, then the possibilities of meeting the demand for natural gas, coal and oil have been determined based on the domestic extraction of individual energy resources. Such a comparison indicates the dominant role of coal in Poland while the extraction of oil and natural gas meets the domestic demand to a greater extent in Ukraine. Over the period 2000-2017, trends in primary energy consumption were different; a 17% increase was noted in Poland, while a nearly 40% decline was noted in Ukraine. The main factors responsible for radical changes in fuel and energy management in Ukraine have been identified: military operations in the east of the country and the annexation of Crimea, demographic changes. These events had a negative impact especially on the volume of hard coal mining in Ukraine; the significant increase in imports from 5.36 to 19.14 million tons in 2011-2017 was necessary for balancing. The balance of foreign exchange for electricity was also compared. Over the past years, this comparison has been favorable for Ukraine, where the dominance of electricity exports over imports is noticeable, which generated revenues of over USD 200 million in 2017.
According to International Energy Agency (IEA) energy security is the continuous supply of energy at acceptable prices. National energy is based primarily on its own energy resources such as hard coal and brown coal. The 88% of electric energy production from these minerals gives us full energy independence. Additionally, the energy production costs from these raw materials are the lowest compared to other technologies. Of these two, the energy produced from brown coal is characterized by the lowest unit technical generating cost. Poland has the resources of these minerals for decades to come, the experience related to mining and processing them, scientific and design facilities and technical facilities and factories producing machines and equipment for their own needs, as well as for export. Coal is and should remain an important source of electricity and heat supply in Poland for the next 25–50 years. It is one of the most reliable and profitable energy sources. This policy may be difficult in the next decades due to the exhaustion of the available resources of hard and brown coal. The conditions for the construction of new mines, and thus for the development of coal mining in Poland, are very interdisciplinary in legal, environmental, economic and reputational terms. Germany has similar problems. Despite the fact that it is an image of a country investing in renewable energy sources, which are pioneers of energy production from RES, in reality hard and brown coal are still the primary sources utilized to produce electric energy.
The article deals with the subject of an important component of energy management, which is the performance of energy efficiency audits in companies. Using the case study analysis, the role of the energy audit was analyzed in the context of improvement of energy efficiency in selected production companies. The essence of legal requirements following from the implementation of the amended Energy Efficiency Act was presented. Specifically, problems and challenges, which refer to the method of implementation of the audit obligation in economic practice, were discussed. Furthermore, the issue of quality and usefulness (in the decision-making process) of prepared reports was raised. It was found that there were indications to claim that the obligatory energy audit of companies is not an instrument for the improvement of energy efficiency, which is always used optimally. The fault in this situation is partly attributable to the state, audit bodies and the company management. In this case, not only is the ineffective communication an issue here, but also the insufficient level of knowledge regarding energy management, as well as haste. The amendment of the Energy Efficiency Act (within just one year) imposed the necessity to conduct an energy audit on a specific group of companies. In principle, because all the entities, to which the obligation referred, had to take actions almost at the same time, numerous issues appeared. Some managers learned about the obligation to conduct the audit from companies who themselves had come out with a proposal to carry it out. This proves the lack of the proper information flow between the government administration authorities and the companies. Again, it turned out that practitioners did not keep pace with the implementation of actions, which were a consequence of numerous (and not always well thought-out) changes in the law. Haste in the fulfillment of the statutory obligation affected a high price spread of the bids sent during tenders, related to the performance of an energy audit. Bureaucratic regulations regarding tenders became another obstacle in the correct performance of the tasks. The entrepreneurs themselves, without clear guidelines on what to expect after the performed energy audit and what a report should look like, on many occasions, selected the “cheapest” bid – not always thinking too much about the qualitative consequences of such a decision. Some certifying bodies – taking advantage of an opportunity and the satisfactory combination of circumstances – offered unprofessional audit services of questionable quality. In the presented conditions, it is difficult to expect real, systemic and desirable results (economically, ecologically and socially) with regards to the energy efficiency both in the micro-, meso- and macr-economic scale. It is worth considering changes in the Energy Efficiency Act and spread the obligation to perform audits over different years according to clearly defined (in cooperation with business) criteria. If relevant actions are not taken, the situation of a temporary Eldorado on the market of energy audits will repeat in 4 years. Again, the consequence may be the poor quality and questionable usefulness of reports from energy audits of companies both at the business level and the ecological-political level. It is necessary to counteract all forms of unfair competition to interdisciplinary and specialist bodies which take actions to improve the energy efficiency of organisations. The creation of appropriate business conditions will have a positive impact on the improvement of energy efficiency. In this context, it is necessary to take actions, which enable the optimization of both the process of the implementation of obligatory legal regulations and voluntary (industry) norms and standards.
A lot of interest has recently been put into the so-called ‘virtual cryptographic currencies’, commonly known as cryptocurrencies, along with its surrounding market. The blockchain technology that stands behind them is also becoming increasingly popular. From the perspective of maintaining energy security, an important issue is the process of mining individual cryptocurrencies, which is associated with very high energy consumption. This operation is usually related to the approval of new blocks in the blockchain network and attaching them to the chain. This process is carried out through performing complex mathematical operations by various devices, which in turn require high power and respectively consume a lot of energy. The impact of cryptocurrency miners on the power and energy demand level might gradually increase over time, therefore this issue shouldn’t be ignored. Comparing the above information in parallel with the growing need for providing demand side response (DSR) services in the Polish Power System, raises the question whether devices used for mining cryptocurrencies can be used for the purpose of balancing the power system. This paper presents an analysis of the possibility to provide the demand side response services by groups of cryptocurrency miners users. The analysis was carried out taking basic functional, technological and economical aspects of these devices’ operations into account.
Electric cars (SE) are currently considered to be one of the best ways to reduce CO2 and other air emissions in the transport sector as well as noise in cities. They can reduce the dependency of road transport on imported oil in a visible way. Nevertheless, the demand for electricity for a large amount of SE in road transport is not insignificant and has an impact on the power system. The article analyzes the potential impact of SE on the demand, supply, structure and costs of electricity generation as well as emissions as a result of introducing 1 million SEs by 2025 on Polish roads, and tripling this number by 2035. The competitive electricity market model ORCED was used for the calculations. The results of the analysis indicate that regardless of the charging strategy, the demand for SEs causes a slight increase in the overall electricity demand in Poland and consequently also a slight increase in power generating costs. Even a large increase in SEs in road transport will result in a rather moderate demand for additional generation capacity, assuming that power companies will have some control over the mode of charging cars. The introduction of SEs will not reduce CO2 emissions compared to conventional cars in 2025, on the contrary will increase them regardless of the loading strategy. In 2035 however, the result depends on the charging scenario and both the increase or decrease of emissions is possible. Electric vehicles will increase SO2 net emissions, but they will contribute to a decrease in the net emissions of particulates and NOx.
Coal reserves in the Czech Republic are estimated to be 10 billion tons – hard coal about 37%, brown coal about 60% and lignite 3%. Hard coal is produced in Northern Moravia. In 2017 the production of hard coal was 5.5 million tons. Brown coal is mined in North-Western Bohemia − the production of brown coal in 2017 was 38.1 million tons. Significant quantities of hard coal are exported to: Slovakia, Austria, Germany and Hungary. In accordance with the National Energy Policy, coal will remain the main source of energy in the country in the future, despite the increased use of nuclear energy and natural gas. The government expects that in 2030 energy from coal will account for 30.5% of energy produced. There are five coal companies in the Czech Republic: OKD, a.s., the only hard coal producer and four brown coal mining companies: Severočeské Doly a.s., owned by ČEZ, the largest producer of brown coal, Vršanská uhelná a.s., with coal resources until 2055, Severní energetická a.s. with the largest brown coal reserves in the Czech Republic and Sokolovska uhelná a.s., the smallest mining company extracting lignite. OKD operates coal in two mines Kopalnia Důlní závod 1 – (consists of three mines: ČSA Mine, Lazy Mine, Darkov Mine) and Mine Důlní závod 2 (ttwo mines Sever, Jih). The article also presents a pro-ecological solution for the management of waste heaps after coal enrichment – a plant for the enrichment of coal waste from the Hermanice heap.
The article presents the current state of the CNG market used as an alternative fuel for car engines. Attention was paid to European Union directives requirements and the current state of the directives’ fulfillment. The economic aspect of CNG usage was analyzed and the approximate costs of driving 10,000 km on different fuels in the last four years were presented. The PtG process which uses electric energy (hydrogen production) and carbon dioxide captured from the flue gas for the production of synthetic methane were discussed. The scheme of the SNG plant with the indication of its most important components was presented, and attention was paid to the mutual complementation of PtG technologies with carbon dioxide capture technology. The benefits of synthetic methane production are presented and the use of compressed natural gas to power engines in vehicles has been described. First, the focus was on the single-fuel use of CNG in bus and truck engines, paying particular attention to the ecological aspect of the implemented solutions. It has been shown that the use of compressed natural gas will reduce almost 100% of the particulates emission from the combustion process. The advantages and disadvantages of the alternative fuel supply are given. Next, the aspect of dual-fuel use in diesel engines was analyzed on the example of a smaller engine. The degree of reduction of harmful compounds emission from the combustion process is shown. Finally, attention was paid to the possible scale effect, referring to the number of motor vehicles in Poland.
Poland is now faced with the task of developing a long-term energy policy for decades to come, a strategy capable of reconciling the security of power supplies as well as effective economic processes, ensuring adequate standards of environmental protection. The process in which fossil fuels are converted into energy carriers of choice is accompanied by the emission of various gas substances which escape into the environment. Later on, those substances accumulate in the atmosphere as greenhouse gases affecting the Earth’s radiation balance – the greenhouse effect. Upsetting the balance between emission levels of those gases and the capacity to convert them in the atmosphere is the reason for climate changes. Sustainable development indices constitute a monitoring tool which makes it possible to create a statistical image of a country from the perspective of a new development paradigm. The most important feature of this index is the capability of comparing values, enabling to determine the position of a given object with reference to other objects. The article analyses 8 indexes of sustainable development in terms of using biomass for power generation purposes. The analysis was performed to include three social order indices, two economic indices and one environmental order index. It was concluded that the use of biomass in power generation can reduce the emission of greenhouse gasses significantly at several stages: the emission can be eliminated from the biological process of biomass conversion, storage and it can also be reduced during transportation.
Wood pellets are classified as a solid biomass type. They are one of the most popular bio-heating fuels used in Europe, especially in the small heating sector, where pellets are burned in low-power domestic boilers. The pellets and automatic pellet-fired heating devices gained popularity due to the increasing air pollution (smog) problem and the low emission limiting campaigns associated with it. Wood pellets are formed as a result of small forestry particles mechanical compression (mainly conifers originated) and they are listed among renewable energy sources. The purpose of the presented studies was to compare the quality of wood pellets used for pellet-fired boilers and to identify, qualitatively and quantitatively, impurities marked in the samples obtained from the domestic market. The application of petrographic analyses, applied so far in relation to fossil fuels, is a presented work innovation for wood pellets. The microscopic analyses were performed on both certified (ENplus/DINplus) and uncertified wood pellets available on the market. Unfortunately, the analysis revealed that the quality requirements were not met, because of the unacceptable contamination presence. The unacceptable organic inclusions in the analyzed samples are fossil coals and their derivatives, coke, and polymeric materials of natural origin. Unacceptable inorganic inclusions determined in the analyzed samples were: glass, slag, rust, pieces of metal, stone powder, plastic, and polymeric materials of inorganic origin.
Coal combustion processes are the main source of mercury emission to the environment in Poland. Mercury is emitted by both power and heating plants using hard and brown coals as well as in households. With an annual mercury emission in Poland at the level of 10 Mg, the households emit 0.6 Mg. In the paper, studies on the mercury release in the coal and biomass combustion process in household boilers were conducted. The mercury release factors were determined for that purpose. For the analyzed samples the mercury release factors ranged from 98.3 to 99.1% for hard coal and from 99.5% to 99.9% for biomass, respectively. Due to the high values of the determined factors, the amount of mercury released into the environment mainly depends on the mercury content in the combusted fuel. In light of the obtained results, the mercury content in the examined hard coals was 6 times higher than in the biomass (dry basis). Taking the calorific value of fuels into account, the difference in mercury content between coal and biomass decreased, but its content in coal was still 4 times higher. The mercury content determined in that way ranged from 0.7 to 1.7 μg/MJ for hard coal and from 0.1 to 0.5 μg/MJ for biomass, respectively. The main opportunity to decrease the mercury emissions from households is offered by the use of fuels with a mercury content that is as low as possible, as well as by a reduction of fuel consumption. The latter could be obtained by the use of modern boilers as well as by the thermo-modernization of buildings. It is also possible to partially reduce mercury emissions by using dust removal devices.
The issue of mercury emission and the need to take action in this direction was noticed in 2013 via the Minamata Convention. Therefore, more and more often, work and new law regulations are commencing to reduce this chemical compound from the environment. The paper presents the problem of removing mercury from waste gases due to new BREF/BAT restrictions, in which the problem of the need to look for new, more efficient solutions to remove this pollution was also indicated. Attention is paid to the problem of the occurrence of mercury in the exhaust gases in the elemental form and the need to carry out laboratory tests. A prototype installation for the sorption of elemental mercury in a pure gas stream on solid sorbents is presented. The installation was built as part of the LIDER project, financed by the National Center for Research and Development in a project entitled: “The Application of Waste Materials From the Energy Sector to Capture Mercury Gaseous Forms from Flue Gas”. The installation is used for tests in laboratory conditions in which the carrier gas of elemental mercury is argon. The first tests on the zeolite sorbent were made on the described apparatus. The tested material was synthetic zeolite X obtained as a result of a two-stage reaction of synthesis of fly ash type C with sodium hydroxide. Due to an increase, the chemical affinity of the tested material in relation to mercury, the obtained zeolite material was activated with silver ions (Ag+) by an ion exchange using silver nitrate (AgNO3). The first test was specified for a period of time of about 240 minutes. During this time, the breakthrough of the tested zeolite material was not recorded, and therefore it can be concluded that the tested material may be promising in the development of new solutions for capturing mercury in the energy sector. The results presented in this paper may be of interest to the energy sector due to the solution of several environmental aspects. The first of them is mercury sorption tests for the development of new exhaust gases treatment technologies. On the other hand, the second aspect raises the possibility of presenting a new direction for the management and utilization of combustion by-products such as fly ash.
The coal fed to gravity enrichment consists of coals coming from different deposits and exploitation fronts. These coals differ in quality parameters, especially the amount of gangue (stone) changing over time. This results in the instability of work, especially jiggers, which have a relatively low accuracy assessed by probable scattering or imperfection rates. This deteriorates the quality of the concentrate obtained, the quality parameters of which change over time. The improvement of jiggers work would be possible by averaging the feed. This process is practically impossible due to the failure to design such a node during plant construction, which are, in most cases, directly related to the shaft. In the article, the authors propose to solve the process of averaging the feed before directing it to the enrichment process in jiggers by introducing its deshaling in vibratory- air separators of the FGX type.
Significant quantities of coal sludge are created during the coal enrichment processes in the mechanical processing plants of hard coal mines (waste group 01). These are the smallest grain classes with a grain size below 1 mm, in which the classes below 0.035 mm constitute up to 60% of their composition and the heat of combustion is at the level of 10 MJ/kg. The high moisture of coal sludge is characteristic, which after dewatering on filter presses reaches the value of 16–28% (Wtot r) (archival paper PG SILESIA). The fine-grained nature and high moisture of the material cause great difficulties at the stage of transport, loading and unloading of the material. The paper presents the results of pelletizing (granulating) grinding of coal sludge by itself and the piling of coal sludge with additional material, which is to improve the sludge energy properties. The piling process itself is primarily intended to improve transport possibilities. Initial tests have been undertaken to show changes in parameters by preparing coal sludge mixtures (PG SILESIA) with lignite coal dusts (LEAG). The process of piling sludge and their mixtures on an AGH laboratory vibratory grinder construction was carried out. As a result of the tests, it can be concluded that all mixtures are susceptible to granulation. This process undoubtedly broadens the transport possibilities of the material. The grain composition of the obtained material after granulation is satisfactory. Up to 2 to 20 mm granules make up 90–95% of the product weight. The strength of the fresh pellets is satisfactory and comparable for all mixtures. Fresh lumps subjected to a test for discharges from a height of 700 mm can withstand from 7 to 14 discharges. The strength of the pellets after longer seasoning, from the height of 500 mm, shows different values for the analyzed samples. The values obtained for hard coal sludge and their blends with brown coal dust are at the level from 4 to 5 discharges. The strength obtained is sufficient to determine the possibility of their transport. At this stage of the work it can be stated that the addition of coal dust from lignite does not cause the deterioration of the material’s strength with respect to clean coal sludge. Therefore, there is no negative impact on the transportability of the granulated material. As a result of mixing with coal dusts, it is possible to increase their energy value (Klojzy-Karczmarczyk at al. 2018). The cost analysis of the analyzed project was not carried out.
en
pl
